Mechanisms: Mechanisms such as tabletops, track grooves, wire ropes,EuroshhazoWhere is there a lift for goods, chains, and pulleys are made of solid materials to ensure safety.In addition, during installation, it is strictly forbidden to use hammers, etc. to prevent damage to bearings or gears due to excessive axial force or radial force. Be sure to tighten the mounting bolts before tightening the force bolts. Before installation, clean the anti-rust oil on the motor input shaft, the positioning boss and the connection parts of the elevator with gasoline or zinc and sodium water. Its purpose is to ensure the tightness of the connection and the flexibility of operation, and to prevent unnecessary wear and tear.Euroshhazo,Simple, in fact, some details should be paid attention to, as follows: It is actually difficult to insert them into the shaft pins when over-installing the bearings, but sometimes, some people think of hammering the bearings for convenience. When using brute force, which is the main reason for bearing damage and reducing the service life of the bearing. Therefore using a hammer to directly hit the bearing will cause great damage to the bearing we must not overdo it when installing the bearing. It is best to put some soft cloth or cardboard on it before installing.The use of elevators is not to maintain and overhaul after the equipment fails. It is necessary to maintain the equipment according to the correct maintenance and overhaul, and start with the preparation work to prevent all possible failures and accidents. I hope that the editor can summarize the knowledge points today. Help everyone.Girishk,How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.What types of lifts are there? There are many types of this equipment, and then the lifting operation can be carried out. This type of lifting equipment is generally used more on the assembly line. Some large-scale production lines need to move the material when loading materials. Lifting to a certain position, and then putting it into the production line for production, a special lifting device is required to be fixed at a certain position of the production line.Safety performance: The lifting structure is made of high-strength manganese steel rectangular tube, with strong stability and high carrying capacity. The maximum lifting height is about meters, and the maximum load is about tons. .

Avoid working in an environment. In the event of rain, snow and other weather, the use of the hydraulic lifting platform should be stopped to prevent the occurrence of a short circuit, resulting in electric leakage and electric shock; non-professionals are strictly prohibited from disassembling electrical appliances such as hydraulic lifting platforms. In the event of an accident, you can’t disassemble without permission to eliminate the cause. You must report to the manufacturer for repair in time, inform the phenomenon of the accident, and the manufacturer will guide you to complete the inspection or send someone to repair it; do not disassemble the appliance without permission! Professional elevator factory guarantees quality, guarantees service. Guarantees quality. Your satisfaction is our pursuit! Welcome to inquire.For the introduction to the daily maintenance of the elevator, the brakes of each organization should be regularly inspected and the distance between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. On the surface, there should be no dirt, and if there is dirt, it must be washed off with gasoline or thinner.Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, mesh type, iron plate seal type.queryPrecautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.Regarding the cleanliness of the hydraulic station, is there any relevant rule requirement?How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.

Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Credit guarantee,Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.The maintenance of the elevator should be refueled regularly: During the use of the elevator, because of the relatively large load, the friction between the various components is also relatively large,EuroshhazoGuide rail type lifting cargo elevator, especially the elevator chain and the elevator shaft pin. It is necessary to ensure that an appropriate amount of oil is added before each use to ensure It is flexible and not stuck when running work. If the elevator is running, once there is a 'squeak' friction sound, it can be basically concluded that the elevator is short of oil,EuroshhazoGuide rail lifting cargo elevator, and the work must be stopped immediately to find out the reason and not to force the operation, which is likely to cause unforeseen hidden dangers. Point summary: Maintenance of elevators requires regular refueling, which is not allowed.The elevator is a kind of elevator equipment composed of traveling mechanism, hydraulic mechanism, electric mechanism and supporting mechanism. The hydraulic oil is under a certain pressure formed by the vane pump, and enters the lower end of the hydraulic cylinder through the oil filter, explosion-proof electromagnetic reversing valve, throttle valve, hydraulic control check valve, and balance valve, so that the upward movement of the hydraulic cylinder can lift heavy objects , The oil returned from the upper end of the hydraulic cylinder returns to the oil tank through the explosion-proof electromagnetic reversing valve, and the rated pressure relief valve is adjusted, and the pressure gauge reads the pressure gauge.EuroshhazoIf the motor of the hydraulic lift is overheated, it must be eliminated in time.Precautions for elevator installation Keep the access road of the external construction elevator smooth and have enough parking space for equipment. When it is necessary to use a steam crane for auxiliary installation, it should be fully considered whether the site environment meets the operating conditions of the steam crane.