XinminMobile scissor hydraulic lifting platformWhat role can it help you
release time:2024-07-10 21:32:20

Attention: Abnormal meshing of gear teeth should be avoided: uneven rolling of the rollers should be avoided; Avoid diagonal orientation of the guide rollers; It should be avoided that the guide rollers are kept at the same time for a long time; The above abnormal phenomena can lead to rapid wear and even scrapping of gears, racks, rollers,XinminSelf propelled platform lifting, and guide rails. If adjusted more carefully, it will be more beneficial for the service life of the elevator.On the contrary, it should be adjusted in the opposite direction; When the meshing backlash of the gear pair is greater than .mm,XinminMobile scissor type lifting platform, loosen the connecting nut of the eccentric shaft of the guide roller and the tooth back pressure wheel as shown in , adjust the tooth back pressure wheel to press towards the back plane of the gear rack until the backlash reaches a reasonable range. Otherwise, it should be adjusted in the opposite direction. At this point, the guide roller should be loosened for o and then adjusted according to the adjustment of the guide roller.Xinmin,Heavy load capacity: protective plate form: ° Or ° Interchangeable configuration rocker working angle: ° Drive method: hydraulic power unit drive or screw drive.  ?? The supervision unit shall effectively fulfill its safety responsibilities, and if any potential production safety accidents are found, it shall require the installation unit and the user unit to rectify within a specified period of time. If the installation unit and the user unit refuse to rectify,Check and repair the electrical circuit and control panel switch components. If there is aging in the circuit, replace itCheck if the usage period of the speed limiter has expired. If it exceeds the usage period,XinminHydraulic aluminum alloy lifting platform, it is necessary to send it to a qualified professional unit for inspection and calibration. What are the functions of the lifting stage device?Regularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found, they must be promptly eliminated.


XinminMobile scissor hydraulic lifting platformWhat role can it help you



On the contrary, it should be adjusted in the opposite direction; When the meshing backlash of the gear pair is greater than .mm, loosen the connecting nut of the eccentric shaft of the guide roller and the tooth back pressure wheel as shown in , it should be adjusted in the opposite direction. At this point, the guide roller should be loosened for o and then adjusted according to the adjustment of the guide roller.Emergency descent: Handle operation or use of manual pressure relief and activation of emergency battery system to implement emergency descent function safety net.Check the wear and clearance condition of the guide wheel of the cargo elevatorProduct surveyCheck and clean the driving gears and guide wheels of the elevator. If there is excessive wear, it is necessary to replace themPlease refer to the instruction manual for the maintenance and maintenance of the elevator to check the braking torque of the brakeRegularly check whether the operation of each mechanism is normal and whether there is any noise. If any faults are found they must be promptly eliminated.


XinminMobile scissor hydraulic lifting platformWhat role can it help you



All connecting shafts must have split pins and be sufficient.Production department,The surface of each part of the brush should be kept clean, and the brush pressure should be adjusted to ensure that its area is not less than %.The vibration frequency should be set to obtain large dynamic stress with low energy consumption, and the resonance frequency should be used to handle time dependent vibration. However, there may be one or more resonance peaks in large components, and using resonance peaks with higher peaks and lower frequencies for aging can achieve optimal results. The resonance frequency needs to be determined by trial vibration, which slowly increases the speed of the excitation motor from , and determines the relationship curve between the amplitude of the workpiece and the motor speed to determine the resonance point of the workpiece. According to the scanning curve, a large acceleration was obtained at r/min, so r/min was determined as the aging frequency.What are the functions of anti rust primer for warehouse cargo elevators?Xinmin,Check the safety interlocking equipment of the first cut door of the hanging cageThe wear rate is fast, and due to factors such as processing, assembly, the friction surface is rough, the mating surface area is small, and the surface pressure condition is uneven. During the operation of the machine, the concave and convex parts on the surface of the parts are intertwined and rubbed against each other. The metal debris that falls off from the grinding process, in turn, acts as abrasive and continues to participate in friction, further accelerating the wear of the mating surface of the parts. Therefore, during the running-in period, it is easy to cause wear on components (especially the mating surface), if overloaded, it may cause damage to the components and lead to early failures.Leakage occurs due to looseness, vibration, and the influence of heat on the sealing surface and pipe joints of the machine; Some casting, processing and other defects are difficult to detect during assembly and debugging, but due to vibration and impact during the operation process, these defects are exposed, manifested as oil (water) leakage. Therefore leakage is prone to occur during the running-in period. Poor, due to the small fit clearance of newly assembled components and the difficulty in ensuring the uniformity of fit clearance due to assembly and other reasons, oil (grease) is not easy to form a uniform oil film on the friction surface to prevent wear. This reduces efficiency and causes early abnormal wear of the components. In severe cases, it can cause scratches or bite on the friction surface of precision fitting, leading to the occurrence of faults.


comment list
  • Bingjue Refrigeration Equipment Sales Company

    After looking for the XinminMobile scissor hydraulic lifting platform from your family for a long time, I mustered up the courage and the quality of the inspection was very good.

  • Alloy casting

    XinminMobile scissor hydraulic lifting platformHow much is the best price, and I will give you a comment, can XinminMobile scissor hydraulic lifting platform be cheaper?

  • Chawanfeng Electric Power Company

    XinminMobile scissor hydraulic lifting platform The quality is not bad, and the goods are delivered in time. I recommend you to buy it next time.

  • Xinhuayu Renewable Resources Company

    I really like it, I am very supportive, the quality is very good, exactly the same as described in XinminMobile scissor hydraulic lifting platform, I am very satisfied, I really like it, completely ex

  • Insurance claims consultation

    I just received it this morning and I like it very much. I'll come next time, can you introduce a friend to buy XinminMobile scissor hydraulic lifting platform for a discount?

©2009-2024Industrial Microblog  Sitemap