Seksad13 meter guide rail type cargo elevatorScrap standard
release time:2024-07-11 09:36:49

It is strictly forbidden for personnel to take the freight elevator to go up and down floors and climb.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Seksad,The elevator incidents that occurred in China in recent years in mobile elevator manufacturers are caused by three factors, namely, human error, which is purely caused by the lack of equipment-related operators. The second type is simple lifts such as hoists that have been eliminated in China and are not allowed to be used. It is aging equipment, more prone to accidents. The third is that the quality of production is not good enough leading to serious social security accidents.The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment,SeksadBuilding elevator,SeksadHydraulic cargo elevator and lifting cargo elevator, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, install Transformation and Maintenance License' to produce, you must ask whether the manufacturer has these two certificates.Dandong City,The last thing to note is that, compared with the lifting platforms in some places, protective fences are generally added on the platforms. Since the lifting platforms are special equipment, the National Quality Inspection Bureau is very strict on this piece of inspection. All must be dismantled, so when the personnel ask you if you want to add a guardrail, don't blindly refuse, and consider whether it is necessary according to the site of use. In addition, you must have the 'People's Republic of Special Equipment Manufacturing License' and the 'People's Republic of Special Equipment Installation, Transformation and Maintenance License' to produce, install, and maintain. Therefore, refer to the level beads on the equipment to judge and debug, and then proceed with the operation; the rollers and slideways confirm whether the roller slideways of the hydraulic lifting platform are dry, and if there is When drying the site, an appropriate amount of butter should be added to ensure the smoothness during operation and to avoid head-to-head wear between mechanical parts.The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.


Seksad13 meter guide rail type cargo elevatorScrap standard



Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.In the daily maintenance of the elevator, if the motor is overheated, stop immediately and continue to run after removing the fault. The motor bearing should be lubricated with good quality.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.Discount,SeksadWhere is there a lift for goods,Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the wires and cables are If there is damage, whether the motor is overheated, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean, and the travel switch points of each safety device must be safe and reliable.The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.System: explosion-proof electronic control system, remote control system, P IC system.


Seksad13 meter guide rail type cargo elevatorScrap standard



Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, the lift also has a lot of safety equipment.Online consultation,Walking: assisted self-propelled, two-wheel traction, self-driving, and car modified.Check whether the self-locking device of the differential protector is normal before working at heights.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.Seksad,The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.The boxes and distribution boxes of the hydraulic lift are always kept clean, and the dust on the electrical equipment is cleaned in time.What is the new price of a fixed lift? Professionally improve the quality assurance of the freight elevator factory. The preferential activities are in progress and new and old customers are welcome to come to consult.


comment list
©2009-2024Industrial Microblog  Sitemap