d. All machines and equipment in a production line can connect with the software of the computer data collection system to complete the timely transmission of data information, can be accurately positioned, and is resistant to impact and vibration Moreover, it has good versatility and combination, and has a variety of C-section steel and size selection to ensure its flexibilityOliveira,Galvanized pipe is actually galvanized pipe. This is mainly because it increases the corrosion resistance of the steel pipe,OliveiraHow much is the I-beam of 28,Oliveira40Cr alloy pipe, so it is evenly coated with a layer of zinc. It can prevent the erosion of other chemicals such as and steam, and protect the steel strip. It is non-destructive and effectively prolongs its service life. Generally, the steel strip purchased is rolled into a large number by the galvanized pipe manufacturer, so pay attention to it during storage.→ compared with the concrete structure,Oliveira16Mn heat expanded seamless pipe, the I-steel structure can increase the service area by %, and reduce the structural design internal force.Taejon, Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.a. In the forming process, the thick steel plate has uniform deformation, small internal stress and no scratch on the surface. The alloy pipe produced and processed has higher coordination ability in the scope of size, specification and model of diameter and wall thickness, especially in the production and manufacturing of steel structure design grade thick wall pipe, especially medium diameter small thick wall pipe, which has incomparable advantages of other processing technologies, and can meet a large number of customer regulations on the specification and model of alloy pipe.

Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, and the technology is relatively perfect. Once the tube size is increased, the automatic control system will be upgraded.There shall be no bending at the welded junction, and there shall be no staggered joint during assembly. Electric welding positioning is generally spot welding. After inspection and straightening, the free conversion method shall be used for welding as far as possible. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.plan,I-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows:Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.Alloy pipe is a kind of seamless steel pipe. Alloy pipe is divided into structural seamless pipe and high-pressure heat-resistant alloy pipe. It is mainly different from the production standard and industry of alloy pipe. Annealing and tempering of alloy pipe changes its mechanical properties. Meet the required processing conditions. Its performance is higher than that of ordinary seamless steel pipe, its utilization value is higher, the chemical composition of alloy pipe contains more Cr, and its performance of high temperature resistance, low temperature resistance and corrosion resistance. Ordinary carbon seamless tubes do not contain alloy components or have few alloy components. Alloy tubes are widely used in petroleum, aerospace chemical industry, electric power boiler and other industries because the mechanical properties of alloy tubes change and are easy to adjust.

Because alloy pipe is a very unique pipe fitting, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.system,The specification of pass design I-beam is expressed in cm of waist width. For example, the waist width of No. I-beam is. The types of I-beam include hot-rolled ordinary I-beam, light I-beam and wide parallel leg I-beam (H-beam). The waist width of hot-rolled ordinary I-beam in China is ~, expressed as No. ~ No. and the inclination of inner wall of leg is : The pass system of rolled I-beam includes direct pass system, cross pass system and mixed pass system. In addition, I-beam can also adopt special rolling method.Galvanized pipes are used in construction, machinery manufacturing, steel construction and other projects, shipbuilding, steel structure engineering, power engineering, power plant, agricultural and chemical machinery, glass curtain wall, automobile chassis, airport, boiler construction, house construction, pressure vessel, oil storage tank, bridge, power plant equipment, Hoisting and transportation machinery and other welded structural parts with high load.Greatly reduce the environmental pollution caused by abrasion, damage and blanking and increase the labor cost of material cleaningOliveira,I-beam: national standard * what is the wall thickness of I-beamAlloy tube is widely used in our daily life, which provides us with great assistance.c. quality inspection is carried out for alloy pipes, so that the whole process of steel pipe processing is under reasonable inspection and supervision, and the product quality is reasonably guaranteed.