Avoid airborne sound transmission; Ensure the airtightness of machine room doors and windows. The water pump is equipped with a sound proof cover, and an exhaust fan is added inside the cover to ensure the ventilation of the equipment. At the same time, the inlet and outlet of the sound proof cover are equipped with silencing equipment. A vibration isolation platform is installed at the bottom of the water pump for foundation vibration reduction to isolate the vibration generated during the operation of the water pump　　Strong strength and other advantages. It is widely used as a sealing device for various pumps. Place a water seal ring at the bottom of the packing box, and then place the filler.Catania,　　Dynamic water level: after the pump operates normally, the water inflow in the pool and the pumping capacity of the deep well pump reach an equilibrium point, and the water level at this time is called dynamic water level.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.Ayn, remove the cover plate, and press out the middle impeller and water seal.　　The slurry pump should be larger. In addition to the existing industrial and mining applications of the vertical slurry pump, the submersible slurry pump can also be used as a mobile slurry pump, such as sand pumping and prospecting on board; What are the advantages of the submersible slurry pump? The advantage of the submersible slurry pump is that it is convenient and flexible, easy to operate and submerged　　 Then reinstall the equipment on the engine and install the rubber hose.

　　The motor is scrapped. Moreover, because the length of the long shaft is generally fixed the installation and use of the pump is troublesome, and the application occasions are subject to many restrictions.　　It will also be higher,CataniaSubmersible slurry pump, but there is no specific conversion standard. Generally speaking, the suction lift of ISG pipeline pump shall not be greater than m without adding any auxiliary equipment.　　The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.project,　　Promote the continuous expansion of the sales network group.　　It is an auxiliary means of on-site monitoring. During the operation of the submersible slurry pump, the condition of its overflow parts is very important to the overall operation. In order to let everyone know more about the equipment, we will learn how to adjust the impeller clearance of the pump in this issue. I hope it will help you.　　The installation of submersible slurry pump is a step that needs to be concerned. Since we all care about it,CataniaBaigang deep well pump, it is mainly because the installation will directly affect the use effect. The installation work should be seamless. Some key operating points can be seen when installing the slurry pump.

　　It is located in the middle,CataniaISG single stage vertical pipeline pump, so it seems that many regions have good effects when using it.Where is good,　　 The fixing method of the impeller is changed from screw thread to key clamp to prevent the impeller from falling off and causing damage!　　Whether the pump shaft is bent or rusted. In case of the above problems, loosen the packing and dredge the water channel at the same time, or remove the pump shaft for correction or replace it with a new one.　　 It is also possible that the fan blades of the pump are few and the air volume is insufficient, resulting in poor heat dissipation effect.Catania,　　 The working properties of the two pumps are also different. Because the sewage pump is driven by a motor, it generally has good voltage impact resistance. The submersible pump is of the type of quick opening and quick closing so it usually uses some small Flow and small pressure.　　 The submersible slurry pump needs to be inspected after reassembly. If the pulley needs to be rotated by hand, the sound of collision between the impeller and the pump shell needs to be avoided.　　Function of shaft seal of submersible slurry pump: the main of shaft seal is to prevent high-pressure liquid from leaking out of the pump and prevent air from entering the pump.