SuriAh slurry pumpIntroduction to process steps
release time:2024-07-11 07:24:13

  Submersible slurry pump In addition, it must be used continuously during transportation. If there is an interval in the middle, it must be avoided that the interval is relatively long, so as to avoid the solidification of slurry in the pump when the operation is stopped.  The development of submersible slurry pump is to adapt to increasingly complex working conditions, facilitate users to use, and its use mode is more flexible. And it fills a part of the gap in the application of slurry pump. When the submergence depth is deep and there is no better slurry outlet,SuriVortex pump and pipeline pump, that is, in the traditional slurry pumpSuri,   Check the surrounding environment: when the ambient temperature is higher than ℃, the temperature of the air inlet will rise, the diameter of the impeller after cutting shall not be less than % of the diameter of the standard impeller, otherwise the of the pump will have a very adverse change. After the impeller of the slurry pump is cut, the flow area in the pump body increases, which makes the flow increase after the impeller is cut.eMbalenhle  Different process requirements: the motor used in the vertical slurry pump is an ordinary vertical motor,SuriQJ submersible pump, which has no waterproof . The motor of the submersible slurry pump and the pump shaft are coaxial. The motor shall be waterproof and sealed. The motor and the pump body can invade underwater at the same time.  Second,SuriZD slurry pump, the power used is not matched, so the motor temperature will be too high after long-term overload operation; In addition, frequent startup during use will also lead to fever, so I   When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body


SuriAh slurry pumpIntroduction to process steps



  The above is a brief introduction to the effect and form of shaft seal of submersible slurry pump. Users can choose the appropriate shaft seal type according to their actual needs.  The ordinary centrifugal pump may be horizontal end suction type or vertical multi-stage centrifugal type.   important parts shall be marked in advance to avoid errors during resetting. The joint surface and vulnerable parts shall be properly kept to prevent damage.Home page recommendation,   Next, the water seal, lock ring and other parts need to be installed.   When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline, and After that, cut off the power supply of the motor. If the temperature of the environment is low, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing body  Potential energy, pumping water up high. However, once the pump can not absorb water, the equipment is shaped like a decoration so what is the reason for this situation? How to solve it?


SuriAh slurry pumpIntroduction to process steps



   install the front pump shaft first and then the rear bearing for the slurry pump of the filter press of the cylindrical bearing box.Welcome calls , so it usually uses some small Flow and small pressure.  Consider the vertical separation level of the tail equipment. The water pump control cabinet has a variety of protection s and complete status display, such as overload, short circuit, phase loss protection, pump body water leakage, motor over temperature and electric leakage as well as single pump and multi pump control working modes, a variety of main and standby pump switching modes and various   The secondary pump shaft seal of the two-stage series pump is (packing seal), and the startup of the series pump also follows the above method. Only after the first stage pump is started, the submersible slurry pump can open the outlet valve of the last stage pump (the opening size is based on the motor current of the first stage pump as the rated powerSuri,  Under the action of auxiliary devices, it can transport the slurry, and because the sealing device itself is special, it can also ensure the internal and external balance of the submersible slurry pump during transportation, so that the pressure at both ends of the equipment can be balanced during normal use   When adding lubricating oil to the pump at ordinary times, the metering must be controlled, and the excess lubricating oil in the pump must be discharged and replaced regularly.   If the head of the submersible slurry pump is too low or the head is higher than the practical condition, the outlet valve can be turned down to increase the resistance to control the current.

comment list
  • Yuanyi Housekeeping Service Company

    The boss is so kind, he really knows his job well. Under your guidance, I will soon become an expert! The seller's service is really attentive. Bring colleagues together in the future. Very good SuriA

  • Elevator manufacturer

    Happy cooperation, give your company support and wish business prosperous.

  • Regis Landscape Engineering Company

    Brother, with your support, this new model SuriAh slurry pump is indeed up to standard and very good.

  • Silicon PU court laying

    I think it’s pretty good. When I bought it, I saw the comments in the comments and I bought it. When I saw the shipment, I was very excited. After SuriAh slurry pump arrived, I was excited and tried i

  • poultry farming

    It’s really a test and waiting. I finally waited for 3 days SuriAh slurry pump to arrive, the opening quality is very good

  • large outdoor advertising

    SuriAh slurry pump Very cost-effective! It is worth buying like everyone! worth having!

©2009-2024Industrial Microblog  Sitemap