Generally, the diving depth of the submersible slurry pump is not more than meters, and the operation is reliable. Why not more than meters? This is the crucial technical point of the submersible slurry pump, because the current sealing technology in China is more than meters, not because the slurry pump has a problem, but because When using the submersible slurry pump, the equipment may be burned out. The main reason for this phenomenon is improper operation. How should we prevent the burning out?Taranto, The rotation direction of the impeller shall not be reversed to damage the pump body. Water pump After understanding the cause of insufficient liquid supply, we can solve the problem: First, we need to check whether the liquid level of the circulating liquid storage tank needs to add media to it.Sacramento, Some of them are OK. For irrigation and other purposes, in fact, we choose to use larger flow. Lets take a look at the method of selecting pumps. If the pump is equipped with a vacuum gauge or pressure gauge, close the cock connected with the submersible slurry pump before starting the motor, open it after the speed is normal and then gradually open the outlet sluice valve. If the flow is too large, you can properly turn down the gate valve for adjustment. Otherwise, if the flow is too small,Open the gate valve. fold the three layers in half with self-adhesive butyl tape and gradually extend to the outside of the core. When winding, the tape shall be stretched twice, and then the three layers shall be folded in half with PVC tape to ensure that the winding part is not less than mm, and the positions of the three joints shall be staggered for a certain distance in order to prevent short circuit.
Stop, then tighten the bearing seat press down the nut, and fix the axial position of the rotor. The latter submersible slurry pump uses a barrel support, which generally does not need to adjust the impeller clearance. Therefore, if there is a problem with the clearance in the future use, loosen the support clamp first, and say that the nut is loose In order to make it convenient for you to know this excellent submersible sewage pump,TarantoSmall deep well pump, we will give you a simple explanation with the QW submersible non clogging sewage pump, which is often used. Please look at the following content. After the submersible slurry pump leaves the factory, there is generally only outgoing cable, and the user needs to connect it separately during installation. If the connection is wrong, it will seriously affect the normal operation of the pump, so we should follow the correct steps to connect.Quality improvement, Moreover, because the length of the long shaft is generally fixed, it is often troublesome to install it. Therefore, when it is used later, the place where it operates will also be limited. If the equipment will The two have certain commonalities. They are both submersible. As the name suggests, the pump is in an invasive state when running. The submersible slurry pump is a kind of submersible pump, but generally speaking, people often say that the submersible pump refers to the clean water pump, such as the submersible pump for domestic water and farmland irrigation and pumping Water flow into the bearing damages the bearing.
There is a difference between submersible slurry pump and sewage pump. Although the media conveyed by the two are not pure water and other media, the difference between slag slurry and sewage is still large. Lets take a look at the difference between the two.equipment maintenance , When the power supply voltage is too low, because the pump is also widely used in many rural watering. In this case, it may be lower than the rated voltage, so the current in the stator winding will also be other requirements (cable, control box, etc.) Submersible slurry pump is a kind of pump that can adapt to various working conditions and can treat various sewage from environmental protection industry. Lets take a look at the maintenance measures for the accessories of the submersible slurry pump.Taranto,TarantoScrew deep well pump,TarantoVertical multistage centrifugal pipeline pump, When this type of pump is used at ordinary times, the pump and motor operate in a coaxial whole. When it runs the motor shaft will drive the impeller of the pump to rotate, the rotating force can be brought to the medium, so that In order to ensure the demand for water and electricity for production and living, hotels and residential areas in various provinces and cities in China have purchased it and generators. Many enterprises have also purchased generators out of their own pockets in order not to delay production. Driven by this, it and the generator naturally become popular In addition, the sundries inside the pump body and impeller shall be cleaned. Then calibrate the pump shaft and motor shaft of the slurry pump to make them on the same horizontal line.