I-beam is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'.The alloy tube can be hardened by induction heating, this kind of steel has been widely used as the material of rolling mill flap ball screw in rolling mill manufacturers. In addition to the excellent properties of cronidur steel, the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment, and its application range is expected to be further expanded.Wells,The production methods of seamless pipe are roughly divided into cross rolling method and extrusion method. The cross rolling method is to drill the tube with a cross roll, and then extend it to the rolling mill. This method has fast production speed, but has high requirements for the workability of the blank. It is mainly suitable for the production of carbon steel and low alloy steel pipes. The extrusion law is to pierce the blank or ingot with a punch, and then squeeze it with a steel pipe with an extruder. The efficiency of this method is lower than that of cross rolling method. It is suitable for producing high-strength alloy steel pipe. The billet or ingot must be heated before cross rolling method and extrusion method. The produced steel pipe is called thermal correlation. Steel pipes produced by hot working can sometimes be cold worked as needed. There are two methods of cold working. One is cold drawing. In other words, pull the pipe to the pipe and tilt it to make the steel pipe gradually thinner and longer. Another method is cold rolling. The method of applying the hot smoke invented by brother to cold processing. The cold working of seamless pipe can improve the dimensional accuracy and finishing of steel pipe, and improve the mechanical properties of materials.Precision cold rolling of small and medium-sized bearing sleeves with alloy tubes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the development of high quality cold drawn bearing steel pipe and its application in bearing. Precision cold rolling of small and medium-sized bearing sleeves with bearing steel pipes can greatly improve material utilization, bearing performance and service life. This paper systematically introduces the service life of high quality cold drawn bearings.Bouca, but the remaining wall thickness must be within the allowable standard.Application scope of alloy pipeWith the development of steel structure buildings, only I-beam is not enough, which is easy to lose stability for load-bearing columns.

H-section steel is an economic section high-efficiency profile with more optimized section area distribution and more reasonable strength weight ratio. It is named because its section is the same as the English letter 'H'. There is no slope on the inner side of the two outer edges of H-section steel, which is straight. This makes the welding and splicing of H-section steel simpler than I-section steel, better mechanical properties per unit weight, and can save a lot of materials and construction time.Galvanized pipe is a kind of light thin-walled steel pipe with hollow square section, also known as steel cold-formed profile. It is a section steel with square section shape and size, which is made of Q hot-rolled or cold-rolled strip or coil as the base material, cold bending and high-frequency welding. In addition to wall thickness thickening, the corner size and edge flatness of hot rolled extra thick wall galvanized pipe reach or even exceed the level of resistance welding cold formed galvanized pipe. Good comprehensive mechanical properties, weldability, cold and hot workability and corrosion resistance,WellsWhat is the price of 273 seamless pipe, and good low temperature toughness.Heating surface pipes, economizers, superheaters, reheaters, pipes for petrochemical industry, etc. for high-pressure boilers (working pressure is generally above MPa and working temperature is between ℃ ~ ℃)Recommendation and consultation,Dry processing technology: after passivation treatment, parts shall be dried with air compression or hot gas, or drying treatment or air drying can be selected.Whether I-section steel is ordinary or light because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members. It is not suitable for axial compression members or members with bending perpendicular to the web plane, which makes it very limited in the scope of application. I-beam is widely used in buildings or other metal structures.Because alloy pipe is a very unique pipe fitting, we must use appropriate methods to carry out installation in the case of installation, so as to ensure the performance index of the data. Generally,WellsHow much is a ton of straight welded pipe, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together.

Small longitudinal crackMarket trend, Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product,WellsWhich is a good welded pipe manufacturer, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole, etc.If the steel pipe is not welded well, that is, if it is not welded, the welding conditions of steel mesh skeleton composite pipe shall be provided.Function of I-beam: where is I-beam mainly used?Wells,According to the national standard of hot rolled H-section steel in China (GB / t- H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members, while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, the moment of inertia of the two main axes of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Ways to obtain surface compressive stress characteristics of alloy tubes