Application characteristics of I-beam:Plan option : Martensitic chromium alloy pipe,Silverson,Longitudinal welded pipe has the advantages of simple production process, high production efficiency, low cost and rapid development. The strength of spiral welded pipe is generally higher than that of straight welded pipe. It can produce welded pipe with larger pipe diameter with narrow blank, and welded pipe with different pipe diameter with blank of the same width. However, compared with the straight seam pipe with the same length, the weld length increases by ~ , and the production speed is low. Welded pipes with large or thick diameter are generally made of steel blank directly, so it is not as high as seamless pipe in its original position. Welded pipe process: uncoiling of raw materials - leveling - end shearing and welding - looper - forming - Welding - removal of internal and external weld beads - pre correction - induction heat treatment - sizing and straightening - eddy current testing - cutting - hydraulic inspection - Pickling - Inspection (strict control) - Packaging - delivery.Nitriding: also known as nitriding, gas nitriding is widely used in the production of alloy steel pipe.Bug, The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.C-section steel has uniform zinc layer, smooth surface, strong adhesion,SilversonHow much is the price of I-beam? How much is a ton, no zinc scar no zinc leakage and high dimensional accuracy. All surfaces are wrapped by zinc layer, and the zinc content on the surface is usually -g /? It has long service life, because the initial temperature of the surface layer is lower than that of the heart and the shrinkage is greater than that of the heart, the heart is pulled. At the end of cooling, because the final cooling volume shrinkage of the heart cannot be carried out freely, the surface layer is compressed and the heart is pulled. That is, under the action of thermal stress, the surface of the workpiece is finally compressed and the center is pulled. This phenomenon is affected by factors such as cooling rate, material composition and heat treatment process. The faster the cooling rate, the higher the carbon content and alloy composition, the greater the uneven plastic deformation caused by thermal stress during cooling, and the greater the final residual stress. On the other hand, due to the change of microstructure during heat treatment, i.e. the transformation from austenite to martensite, the increase of specific volume will be accompanied by the expansion of workpiece volume, and each part of workpiece will undergo phase transformation successively, resulting in inconsistent volume growth and structural stress. The final result of the change of tissue stress is the tensile stress on the surface and the compressive stress in the center, which is just opposite to the thermal stress. The microstructure stress is related to the cooling rate, shape and chemical composition of the workpiece in the martensitic transformation zone.

Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.Thin wall steel pipe, thick wall steel pipe. The small length of repair welding is mm; The raw material shall not exceed mm after grinding by welding edge.Economic management,However, what we need to do now is to improve the production technology level of China&#;s production process of C-section steel, and step up the formulation of relevant industry standards and inspection standards. C-section steel manufacturers should keep close contact with truck manufacturers and communicate more. In this way, it is more conducive for C-section steel manufacturers to produce C-section steel products suitable for truck industry.When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold,SilversonHow much is a 12cm I-beam per meter, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.I-beam is a long strip steel with groove section, which belongs to carbon structural steel for construction and machinery. It is a section steel with complex section, and its section shape is groove shape. China&#;s imports of I-beams are greater than its exports. The main producing areas are Tangshan Iron and steel, Baotou Iron and steel, Shangang, huangte, Maanshan Iron and steel, Japan iron and steel, etc.

Miscellaneous scabQuality recommendation,All the cracks occur at -mm away from the edge below the alloy pipe, and the macroeconomic orientation is vertical to the cold rolling orientation, showing a 'high mountain' shape.The reinforcement mesh of the maintenance platform has the characteristics of extensive application, beautiful style convenient installation and durability, Skirting plate (edge guard plate), checkered plate guard plate, installation of connectors and other accessories can be added around. The reinforcement mesh is suitable for the reinforcement mesh manufactured in the factory and welded with cold-rolled ribbed reinforcement or cold-rolled smooth round reinforcement. The welded reinforcement mesh for reinforced concrete is a good and efficient material for concrete distribution. Flat steel with different specifications can be used for edge wrapping, Or wrap edges with angle steel, channel steel, square tube, etc; Handles and hinges can also be installed on the reinforcement mesh that needs to be moved or opened frequently.After isothermal quenching treatment the modified LNs steel of case hardening steel also has the surface compressive stress characteristics obtained by heat treatment.Silverson,Alloy pipe is a very important way and type of seamless steel pipe. Its use is relatively common. It is widely used in various engineering projects, house construction and building decoration. Its fracture will always be found in the production, manufacturing and key marketing of alloy pipe, That is, many stages of production and processing are not done well. Another is that the seasoning is not enough and the proportion of chemical molecules is wrong. There are all reasons.After determining the reasonable pickling agent and polishing solution, it is very easy to carry out hot galvanizing for relevant alloy pipes. Use 'phosphating treatment' to degrease the pipes of electrolytic machine equipment, put them into the aqueous solution with zinc salt after pickling and passivation, connect the negative level of electrolytic machine equipment, put them into the cold-rolled steel plate in the direction corresponding to the pipes,SilversonAlloy tube, and connect the switching power supply, If the current flows from the positive stage to the negative stage, a layer of zinc is deposited in the pipe.According to the theory of steel structure, the I-beam flange should be stressed, that is, the I-beam should be standing rather than lying down.