NingxiaPlatform hydraulic liftingWhat is the indispensable market driving force
release time:2024-07-10 19:21:11

Remove the hydraulic oil tank filler cap, filter cover, inspection hole,NingxiaFoot hydraulic lifting platform vehicle, hydraulic oil pipe and other parts to avoid dust when removing the system oil pipe. Clean the disassembled parts before opening them. When disassembling the hydraulic oil tank filler cap, first remove the soil around the tank cap, loosen the tank cap, and remove any remaining debris from the joint (do not rinse with water to prevent water from seeping into the tank). After confirming cleaning, open the tank cap.Reason: The lowering valve is not tightly closed. Cleaning method: Check if the lowering valve is powered on. If there is no power supply, clear the malfunction of the lowering valve itself or replace the lowering valve. It is necessary to keep the valve of the lowering valve clean and flexible.Ningxia,Hydraulic cargo elevator: Only when the load of the hydraulic guide rail type lifting cargo elevator cannot start working,Ningxia10 meter hydraulic lifting platform, should the pressure of the hydraulic system be checked. If the pressure is below the normal range, the set value of the relief valve should be adjusted. Professional elevator manufacturers have high pressure resistance, good waterproof performance, fire and high temperature resistance, strong overload capacity, corrosion resistance, radiation resistance, and long service lifeOil leakage from the oil cylinder: If it is a problem with the sealing ring, replace the sealing ring. If there are debris or debris on the oil cylinder,NingxiaHydraulic lifting platform, it is recommended to replace it with a new one.Arad,After hours of elevator operation, perform minor repairs to the mechanical and electrical systems. Road noise can also occur if tires are crushed against objects that are prone to noise. The shaking amplitude of the scissor type lifting platform is proportional to its lifting height. The higher the height, the greater the shaking. When using it at a working height of meters if possible, please use safety protection measuresThe classification of lifting platforms is as follows: they are divided into mobile lifting platforms, hydraulic lifting platforms, folding arm lifting platforms, and sleeve type lifting platforms according to their different modes of movement.


NingxiaPlatform hydraulic liftingWhat is the indispensable market driving force



Aluminum alloy elevators are different from other forms. This type of elevator is made of aluminum alloy material, which is lightweight and has a more beautiful appearance. The disadvantage is that it has a light load capacity and is only suitable for simple high-altitude maintenance work, and can only provide support for - people.The lifting platform is mainly used for the up and down transportation of goods between various working floors, but it may slowly rise during use. When the equipment is working, it mainly uses hydraulic motors to drive hydraulic pumps. So what is the reason for the slow movement? Professional elevator manufacturer with large quantity and excellent quality at a reasonable price. Fire resistant, waterproof, high temperature resistant, sturdy and durable, safe and reliableThe hydraulic elevator overflow valve can also generate high noise. When air is mixed in hydraulic oil, the overflow valve is stuck or severely worn, the spring of the overflow valve is fatigued and deformed, resulting in unstable pressure regulation of the overflow valve, and the relief time of the overflow valve is too short, it is easy to cause the pilot valve performance of the overflow valve to be partially stable, causing air to vibrate inside the pilot valve and generate noise. So we need to regularly clean the overflow valve. When the overflow valve is damaged or severely worn, it should be replaced.Inspection basisThe development of elevators is at its peak, as many manufacturers have chosen more multi-story buildings to fully utilize the site, so they also need a device to facilitate the improvement of goods.Regularly check whether each organization is functioning properly and whether there is noise. If problems are found they should be promptly cleaned up.Pre install equipment, maintain unobstructed access roads and sufficient parking space before pre installation. Some hydraulic cargo elevators require heavy lifting assistance for installation, some require equipment such as forklifts for installation, and some can be pre installed manually. When it is necessary to install with the assistance of a truck crane and a forklift, full consideration should be given to whether the on-site environment meets the working conditions of the truck crane.


NingxiaPlatform hydraulic liftingWhat is the indispensable market driving force



When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than %. The meshing gap should be appropriate.demand,Each box, distribution box, etc. should be kept clean and promptly cleaned of dust on electrical equipment.In on-site hydraulic elevators, it is difficult to detect the rising position, impact noise, and oil film leakage of hydraulic cylinders. Field observations have shown that the excessive lifting speed of the hydraulic cylinder has led to an increase in failure rate, seriously affecting production efficiency. The unstable hydraulic lifting requires an analysis of the hydraulic oil flow rate. Hydraulic pressing oil has poor quality and contains a large amount of impurities, which can also prevent slow and unstable lifting. In addition there are other reasons: lifting the composition of the hydraulic ring. Oil pump, safety valve, directional valve, directional valve, which has been favored by a large number of enterprises and individual customers. Hydraulic elevator is a multifunctional heavy loading and unloading mechanical equipment. The lifting system of hydraulic elevators is driven by hydraulic pressure, also known as hydraulic powered elevators.Ningxia,The main device does not engage. When this fault occurs, check whether the three-phase power supply is normal, whether the internal and external emergency stop button switches, the electric lock switch are turned on, whether the three-phase electrical phase sequence is correct, and whether the relay working indicator light is on.Reason: The lowering valve is not tightly closed. Cleaning method: Check if the lowering valve is powered on. If there is no power supply, clear the malfunction of the lowering valve itself or replace the lowering valve. It is necessary to keep the valve of the lowering valve clean and flexible.Separate: Loading and unloading on different platforms.


comment list
©2009-2024Industrial Microblog  Sitemap