Extrusion method: This production method is to cast copper ingots after smelting, and extrude copper tubes by large extruder after secondary heating.If you want to make the copper surface become bright again, you can polish it with copper point solution. It can not only make the copper surface brighter but also quickly remove the rust and oxide layer on the copper surface to restore the luster of the copper itself.Surigo, forming white smokeThe evaporated zinc is immediately turned into zinc in the air, which brings great difficulties to the operation and affects the health of welders. Therefore, in the places where decorative brass pipes are welded, ventilation and other protective measures should be strengthened. The poor weldability of brass will cause problems such as pores, cracks, zinc evaporation and so on.In August, the price of domestic medium and heavy plates fell sharply. As of August , the price center of ordinary carbon boards in leading cities had dropped to , down yuan/ton from the end of July. At the beginning of the month, affected by the macro bad news, and the recent poor performance of fundamentals, the market mentality turned to pessimism, and some traders shipped at low prices. The market inventory rose, the inventory pressure was high, the stock shortage phenomenon disappeared, and the market transaction atmosphere was cold the demand performance continued to decline, and the spot price fell under pressure.Kahramanmaras, the price of domestic copper bar fell. According to the monitoring data of Lange Steel s cloud business platform, the average price of * mm hot rolled strip in key cities in China is , down yuan from yesterday. Futures prices fluctuated, and the prices of spot market manufacturers eased slightly today. According to the feedback, the market was mainlysee yesterday, which caused the overall transaction blocked, and the mainstream manufacturers prices fell today.Remove the flame. If the filler metal does not melt continue to heat the joint and try again. The melted filler metal is sucked into the casing port according to the capillary effect until a complete filler metal ring appears on the casing port. Remove the flame Pay special attention not to let the flame directly contact the filler metal. It should be the heat at the joint that melts the filler metal. In order to clean the copper pipe,SurigoRed copper bar, the welding flux must have a degree of corrosivity, and shall be cleaned after brazing. The so-called & quot; self-cleaning& quot; fluxes are generally not recommended because of their corrosivity.The simplest way is to use copper cleaner. Brass, red copper, bronze, fingerprints, oxide layers, etc. on the surface can be cleaned with copper cleaner first.

The production method of soft copper tube is basically the same as that of hard copper tube, that is, after annealing, the copper tubes will become soft, which makes it easier to bend. The copper tubes produced in this way are called soft copper tubes.The water quality at the place where the copper pipe is required to be installed shall be studied, and the appropriate water quality and water flow shall be selected for pipe distribution to prevent the root cause.Disadvantages of copper pipe As far as copper pipe is concerned, high production cost and high price are its biggest disadvantages. Compared with other pipe fittings, the cost of copper pipe is much higher, and the connection at the copper pipe interface requires high construction technology level.Direct material,Surigo2507 stainless steel plate,This week (-, the market price of red copper bar rose, and the transaction was not ideal. On the bidding day of Shagang last weekend, the price was stable to support the market, and the price of variety wire rods also rose by yuan at the weekend. However, it was reported that the deal was very poor, which led to the price being s table for the next two days. Until Wednesday, due to the negative outlook on the future market and the reduction of steel billets in the afternoon spiral diving, the market lowered the price. Market price changes, Xinji rose yuan on the rd; For the future market, the off-season is coming, the demand is weakening, and the market wait-and-see mood is getting stronger. But when winter comes, the environmental protection inspection is becoming more and more strict, which supports the market. It is expected that the price ofety wire rod will be adjusted in a weak way in the short term.When welding, just add enough filler metal to fill the capillary gap. Too much filler metal will only form a ball at the bottom of the joint or run into the pipe.If you want to make the copper surface become bright again, you can polish it with copper point solution. It can not only make the copper surface brighter, but also quickly remove the rust and oxide layer on the copper surface to restore the luster of the copper itself.

The composite method of three production methods of copper tube is also a high-tech production method for this method. It is a copper material containing impurities. Those copper materials,Surigo5083 aluminum bar, and then the material is purified to produce copper tube materials.Promise and keep promise,Extrusion method: This production method is to cast copper ingots after smelting, and extrude copper tubes by large extruder after secondary heating.{} The excellent performance of copper pipe The welded copper pipe has the characteristics of firmness and corrosion resistance, which makes it a suitable choice for modern contractors to install the water pipe, heating pipe and refrigeration pipe in all residential commercial houses.First of all, we should set up a warehouse. The temperature in the warehouse should be generally kept at - ° C, while the humidity should be normal. The room should be kept ventilated.Surigo,Disadvantages: low output, high production cost and high price. Extrusion copper tube process is a stable and excellent copper tube production method at home and abroad at present. Only the copper tubes produced by this process are more suitable for the field of heating and ventilation, which is the development direction of copper tube industry in the future.Red copper plate has ductility. Pure copper, which is as big as a drop of water, can be pulled up to two kilometers of thin wire or rolled into a transparent foil larger than a bed. The most valuable property of red copper row is that it has a very good conductive , second onlyver in common metals. But copper is much cheaper than silver, so it has become the & quot; protagonist& quot; of the electrical industry.The room temperature tensile strength of the annealed red copper sheet is ~ kgf/mm, the elongation is ~%, and the Brinell hardness (HB) is ~