Defects of alloy pipe and solutions:The core of C-section steel is the structural system of braced frame. More than half of such senior managers in China are the former. Unfavorable to earthquake resistance. Hydraulic power, and the power is large, generally about KW, which is similar to the plate shearing and bending machine. The general control process is complex, and PLC control is mostly used.Rodas,When the beam width is small, the reinforcement shall be bent.Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings.Giyon,Plan scheme : high carbon steel with carbon content exceeding .% and alloy pipe with chromium content not less than %Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different,RodasIncoloy825 alloy pipe, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design the use of I-beam should be reasonably selected according to the mechanical properties, chemical properties, weldability and structural size of I-beam.When it is used for ground heating and hot spring transportation, it can meet the requirements of refrigeration and achieve the practical effect of less damage. It is applicable to water conservancy engineering, mining and other industries to meet the provisions of cold, cold and corrosion prevention. In addition, the chemical raw material transmission pipeline has a wide indoor space.

The crack mainly occurs at -mm from the edge of the alloy pipe. The shape is several parallel vertical cracks of different sizes. The regularity is that the thicker the specification and model of the alloy pipe is The wider the width, the more serious the disadvantages.Since the s,RodasSteel bar cutter type 50, with the rapid development trend of high-quality hot strip mill production and the development of electric welding and testing technology, the welding quality has been continuously improved, the types, specifications and models of welded steel pipes are increasing, and seamless pipes have been replaced in more and more industries. Welded steel pipes are divided into straight seam welded pipes and spiral welded pipes according to the way of welding. Classified by production mode: classified by processing technology - electric arc welded pipe, resistor welded pipe, (high frequency, low frequency) gas welded pipe, furnace welded pipe. Direct rolling pass system. The direct rolling pass system refers to the pass system in which the two open legs of the I-beam pass are on the same side of the roll axis at the same time, and the waist is parallel to the roll axis.High quality and low priceDefects of alloy pipe and solutions:The working principle of flat steel finishing machine in I-beam production process is to pre level and finally level the cold flat steel with two groups of leveling wheel sets staggered up and down in the thickness direction; A pair of finishing wheels arranged relatively are used to extrude the width direction, so that the width is compressed to achieve the expected parameters, and the compression amount is adjustable; Straighten the width with staggered straightening wheels.Determined by the shape, the section modulus, moment of inertia and corresponding strength of I-beam are obviously better than those of ordinary I-beam with the same single weight. When used in metal structures with different requirements, it shows its superior performance in bearing bending moment, pressure load and eccentric load. Compared with ordinary I-beam it can greatly improve the bearing capacity and save metal by % ~ %.

Key technical characteristics of alloy pipe:Promise and keep promise,RodasHow much is I-beam per square meter,Because alloy pipe is a very unique pipe fitting, so as to ensure the performance index of the data. Generally, when installing alloy pipes, we will use some flanges and elbows to fix them, so as to ensure that the raw materials can be fixed very well. Therefore, when we carry out use, we must ensure the quality of flanges and elbows, so as to ensure the actual effect of alloy pipe assembly. If there are instrument panel components that must be assembled on the pipeline, they must be installed together. Pickling: if the material cannot be removed after cleaning, pickling will be selected. Pickling of galvanized pipe is divided into chemical and electrolytic. How to prevent white rust of galvanized seamless steel pipe? It has a certain anti-corrosion effect on the pipeline.H-beam is a widely used profile in steel structure buildings. It is different from I-beam. The first is the flange, and the second is that the inner surface of the flange has no inclination, and the upper and lower surfaces are parallel. The section characteristics of H-beam are obviously better than those of traditional I-beam, channel steel and angle steel.Rodas, H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, whether it is fire water system software, or pipeline, heat and national defense industrial pipeline system software of petrochemical pipeline system, alloy steel pipe stimulates important effects.→ under the same section load, the weight of hot-rolled H steel structure is reduced by % - % compared with the traditional structure.