Fixed loading and unloading bridge: The fixed loading and unloading bridge is a specialized auxiliary equipment for achieving rapid loading and unloading of goods. Its height adjustment function uses a bridge between the truck and the cargo platform in the warehouse, and forklifts and other vehicles can move and load goods in batches inside the truck. Only one person can work to achieve rapid loading and unloading of goods. It enables enterprises to reduce a large amount of labor, improve work efficiency, and obtain greater economic benefits.Function: Convenient unloading, strong stability, lifting platforms, and unloading platforms: anti slip device: This device is welded from steel plates, which can effectively achieve anti slip function and is safe and reliable. Various legitimate qualifications for boarding bridge factories. Welcome to inquire by phone and sincerely invite cooperation!Komarom ,The lip plate is connected to the platform using a full length shaft, which has high strength and good reliability.At the beginning, it is essential to inspect and maintain the fixed hydraulic boarding bridge before or after use, and pay attention to whether it can be used correctlyUzhhorod,　　. Mobile loading and unloading bridge: used in places without loading and unloading platforms or where mobile loading and unloading of goods is required. If there is no loading and unloading platform at the logistics site, as a remedial measure, a mobile boarding bridge is a very suitable solution. The mobile boarding bridge is equivalent to a moving steel structure slope, and forklifts can also directly drive into the truck carriages for batch loading and unloading operations. What should I do if the hydraulic cylinder of the boarding axle leaks oil? The hydraulic cylinder is a relatively important component in hydraulic equipment responsible for the lifting and lowering work of the equipment. When there is oil leakage in the hydraulic cylinder, everyone must take it seriously.The anti slip device of the auxiliary equipment for loading, unloading,Komarom Hydraulic electric fixed boarding bridge, and handling of goods applied: This equipment is made of thick steel plate welded by electric welding, there is no need to excavate or pre bury the indoor space of tunnel construction on the loading and unloading platform, and most of the buildings do not need to be modified in terms of structure.The use of imported seals ensures excellent sealing performance of the hydraulic system.Once again, whether the site selection, pit design, as well as whether there is construction, will affect the service life and safety of the fixed hydraulic boarding bridge.Installation requirements,　　. Platform side boarding bridge: The platform side boarding bridge is directly installed at the front edge of the loading and unloading platform. There is no need to excavate or reserve pits on the loading and unloading operation platform, and there is basically no change to the building structure. During construction the factors of loading and unloading operations were not taken into account. The platform type loading and unloading bridge serves as a remedial solution and can also meet the requirements for loading and unloading operations into truck carriages.It is made of highly resistant reinforced rubber. The four outer corners of the anti-collision block are all arc-shaped and all bolt holes are deeply embedded inside. Bolt hole size is Ф . Anchor bolt structure for M assembly: The fixed boarding bridge is composed of mechanical system, hydraulic system,Komarom Mounted axle hydraulic fixed type, and electrical system. The platform and chassis form a mechanical system. The platform is based on&quo; U” Shaped steel as the skeleton, with light self weight and large bearing capacity; The countertop is made of anti slip patterned steel plates and has a high load-bearing capacity; The countertop is made of anti slip patterned steel plates, and can withstand a speed of kilometers/hour when the forklift is fully loaded without bending, improving work reliability.The platform type boarding bridge is also designed in various structural forms according to different on-site conditions. It can also be adjusted up (below the cargo platform) or down (below the cargo platform) within a certain range, which can meet the installation and use of most loading and unloading platforms.

The guide sleeve has air holes, sand holes,Komarom Fixed hydraulic boarding bridge, shrinkage, and other conditions. Generally, there is a problem with the casting, which is the quality of the oil cylinder itself. At this time, it is necessary to find a manufacturer to replace the new boarding bridge. Normally, this situation does not occur in the casting oil cylinder. The above two reasons are due to the occurrence of excessive oil leakage, and frequent inspections should be conducted in these two areas. Hydraulic loading and unloading bridge is a specialized auxiliary equipment that maintains rapid loading and unloading of goods during the application process. The height adjustment function of the equipment makes the bridge in the middle of the truck guide sufficient to be built. Lifting platforms, trucks, and hydraulic loading and unloading bridges are commonly used cargo loading and unloading equipment.Good quality,Its design is usually fully standardized as early as the structural design of buildings.The following is a brief introduction to the storage of hydraulic oil in fixed hydraulic boarding bridges for a wide range of users: when stopping the hydraulic oil drum and filling, it is necessary to achieve three passes and pass when receiving oil; Filtering during barrel rotation: When refueling the equipment, it is too cold to ensure the cleanliness of the bucket mouth, oil injection port, oil barrel, etc., to prevent impurities from entering the oil port and forming hydraulic oil purification.Anti collision block: This device can effectively protect buildings and boarding bridges from damage.Komarom , as the name suggests, refers to the boarding bridge embedded in the loading and unloading operation platform. The installed boarding bridge main board surface is horizontal with the upper plane of the loading and unloading operation platform. Completely integrated into the platform, it will not affect other operational tasks on the platform without loading and unloading operations. The boarding bridge with this type of structure is widely used and is also a relatively fast boarding auxiliary device.Its design is usually fully standardized as early as the structural design of buildings.Firstly, as the fixed hydraulic boarding bridge is used to complete the rapid loading and unloading of goods through height adjustment plates, there are certain strict requirements for the quality and material selection of height adjustment plates to avoid the occurrence of defective materials which will result in unexpected loss of performance in the application process.