Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, remove the motor shaft key.Naturally connect the motor to the lift. When connecting, it must be ensured that the concentricity of the output shaft of the elevator is consistent with that of the input shaft of the motor, and that the outer flanges of the two are parallel. If the concentricity is inconsistent, it will cause the motor shaft to break or the elevator gear to wear.Mesworth,Introduction to fixed boarding bridge Loading and unloading mobile boarding bridge is a very easy-to-see structure in the modern logistics scene. It is the point and end point of the enterprise's logistics chain, and a loading and unloading operation platform for the enterprise's fast and turnover products and goods. The height of the loading and unloading operation platform is fixed, but there is always a certain height drop or gap between the height of the transport vehicles and the loading and unloading platform. As a result, the handling forklift cannot directly load and unload goods in and out of the transport vehicle. Utilize a boarding bridge to provide a reliable connection. It enables the forklift to move in and out of the transport vehicle efficiently and quickly for loading and unloading operations.Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem,Whether it is used outdoors or indoors, some small problems will inevitably appear after a long period of time. At this time, what we should do is to maintain and maintain the elevator. How to follow the steps correctly It has become a difficult problem, and I will answer it with you.Are the water cooling and air cooling of the hydraulic station the same?Guide rail lift (also known as freight elevator) is a non-scissor hydraulic lifting platform, which is mainly used in industrial plants, restaurants, restaurants warehouses,MesworthThree ton lifting cargo elevator, docks, workshops and other places that need to move goods vertically between high-rise buildings above the second floor. The low height is especially suitable for sites where the site is not suitable for digging pits. What problems do we need to pay attention to in these places where elevators are used?

The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.Many times when ordering a large lifting platform, after the customer determines the parameters, the designer will first consider various factors before designing, including the size during transportation, to prevent it from being difficult to transport to the customer's installation site after being too wide so When designing and manufacturing, it should be considered that separate assembly or split table can meet the requirements. At the same time, it is also necessary to consider the bearing capacity of the split, and design and manufacture on the premise of ensuring the load capacity and stability, so as to ensure that the equipment can be conveniently transported, hoisted and moved.Features of hydraulic lifts: According to the working mode, hydraulic lifting platform products are divided into crank arm hydraulic lifting machines, scissor hydraulic lifting machines mast type hydraulic lifts, and straight arm hydraulic lifting machines. The hydraulic lift is a replacement product of the folding arm lift (lifting platform) and the scissor lift (lifting platform). It can be widely used in stations, docks, airports, hotels, municipal gardens, garages, cleaning companies, public building facade decoration,MesworthWhere can I sell elevators for goods, decoration or installation and maintenance of power systems, etc. The lift has the advantages of light weight, self-propelled, electric start, self-supporting legs, especially the ability to cross obstacles for high-altitude operations and the like.Interpretation and observation large working area, it is often exposed to rain and sunlight, so special attention should be paid to regular maintenance and inspection to avoid accidents.When installing,MesworthOutdoor lifting cargo elevator, dismantling and adjusting the slewing mechanism, care should be taken to ensure that the centerline of the slewing mechanism reducer is parallel to the centerline of the gear, the meshing surface is not less than %, and the meshing clearance is suitable.

In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and its damage is close to zero. His steel wire rope should comply with the corresponding configuration requirements, and there is no problem of broken strands and diameter reduction. Of course the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.Which one is better,In the construction elevator, the switch box also has leakage protection equipment. Its wires and cables are well insulated, without leakage, and the metal threaded is not rusted, and there is no problem of broken strands and diameter reduction. Of course, the number of broken wires should not exceed the corresponding standard. His pulley movement is very flexible.The hooks of the seat belts are prohibited from being hung on unstable or moving objects.It is best not to cover the aerial work vehicle and park the vehicle outside. If it is windy and rainy, the clothing will repeatedly slap the car paint, especially if the car blows sand on the clothes, it will draw many fine scratches on it. Because it will turn black over time. In addition, when the wind does not directly spray powder or clean the sand on the mechanism, but it should be washed with water, and prevent the sand particles on the paint surface from being scratched by the vacuum cleaner.Mesworth,The motor connection is wrong. When the delta connection motor is wrongly connected into a star shape, the motor still runs with full load, and the current flowing through the stator winding will exceed the rated current, and even cause the motor to stop by itself. If it overheats, it will burn out. When the star-connected motor is wrongly connected into a triangle, or the motor with several coil groups connected in series to form a branch circuit is connected in parallel with two branches, it will cause the winding and core to overheat, and in severe cases, the winding will be burned.The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable, steering, tilting, telescopic), with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, large load capacity, etc., effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.