Zhejiang5-ton factory lift cargo elevator,

Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.When the freight elevator breaks down, professionals should be invited to repair it, and the freight elevator cannot be altered without authorization.Zhejiang,ZhejiangGuide rail lifting cargo elevator,After careful inspection, it was found that it was mainly caused by two reasons. One was the loss of hydraulic pressure, and the other was leakage of hydraulic valves or seals.Always check all wires and cables for damage. The damaged part should be bandaged and replaced in time.Beijing,Always check the connections of the various parts of the hydraulic lift, and tighten them if they are loose. The tightness of the connecting bolts of the body should be checked when the body is under pressure.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The cleanliness of the hydraulic station is an important aspect of the elevator hydraulic station, so it should not be careless. Moreover, from a professional point of view, there are relevant rules and requirements, and you should refer to the specification manual, so that you can have a correct understanding and know how to achieve better cleanliness.

Are the water cooling and air cooling of the hydraulic station the same?Check before use Carefully check the grounding wire, safety device, buffer spring, etc. before use. Make sure it has a safe usage environment.Pay attention to check whether there are any broken wires and loose strands in the wire ropes of each part. If it exceeds the relevant regulations,ZhejiangThe cargo elevator is, it must be replaced immediately. The maintenance of the wire rope should be strictly in accordance with regulations.Promise and keep promise,The design of the hydraulic lifting platform is unreasonable. When the designer designs the cylinder barrel and rod, if there is a problem with the design size and angle, then there will definitely be problems in the later stage. Therefore it is necessary to confirm the technical strength of the manufacturer when working on a hydraulic lifting platform; what is the problem with the sound of the oil cylinder of the hydraulic lifting platform? Design drawings to make, the angle of the oil cylinder is slightly deviated, it will cause the friction between the cylinder barrel and the rod, which will cause the sound; the seal quality of the hydraulic lifting platform is different, and the use of different seals will also affect the sound of the oil cylinder, and the seal with excellent material The continuous friction between the parts and the cylinder wall will cause the sound to be very loud, so when the hydraulic lifting platform is used, pay attention to ask the manufacturer what brand and material the seal is used; In some cases of mechanical running-in, it is not ruled out that the above three situations are normal, and there will still be noises. If there is no problem after investigation, then don’t worry. It’s just a running-in problem between mechanical parts. It will disappear naturally.Are the water cooling and air cooling of the hydraulic station the same?The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.

How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector, and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.Home page recommendation,The hydraulic lifting platform is mainly the pressure transmission of hydraulic oil to realize the lifting function. Its scissor mechanical structure makes the lift stable and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.Power unit adjustment, whether it is a scissor lift platform or a rail-type lift, is controlled by the power unit and the oil cylinder. The power unit is equipped with four outlet holes during production, which can be adjusted in size to increase or decrease the oil cylinder. Hydraulic oil flow, we can adjust the motor speed or the electro-hydraulic proportional valve to adjust the hydraulic oil flow; what factors will affect the lifting speed of the hydraulic lift oil pipe, the longer the hydraulic oil pipe, the longer the rise time. Therefore, during installation, the length of the oil pipe should be reduced as much as possible within the allowable range of the design; on the basis of adjusting the power unit, the size of the oil pipeline can also be adjusted, and on the premise of ensuring that the equipment meets the normal requirements and safety, corresponding adjustment.Many customers think that the operating power supply of the hydraulic lifting platform is below the safe voltage of V, and there will be no electric shock. They are wrong. Normally, there will be no electric shock, but if there is improper operation, it will still be very dangerous. So how can we effectively prevent the occurrence of electric shock accidents? Today, the editor will share safety knowledge with you.Zhejiang, and the wide operating platform and high carrying capacity make the high-altitude operation wide and suitable for many people work at the same time. It makes high-altitude operations efficient and secure.The contact opening and closing of the travel switch of each safety device must be reliable and the contact arc crater should be polished in time.Before the elevator manufacturer connects the motor to the elevator, please screw on the mounting bolts at any diagonal position first please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?