VibelHorizontal slurry pumpRequirements for equipment
release time:2023-01-17 08:24:48

   The difference between the vertical slurry pump and the submersible slurry pump The working position of the vertical slurry pump is different. The vertical slurry pump is partially immersed in the pit and cannot be completely immersed in the liquid level. The submersible slurry pump can be completely immersed (including the motor part) below the liquid level; Use of motor for vertical slurry pump   When stopping the operation of the submersible slurry pump, close the cock of the vacuum gauge and pressure gauge and the gate valve on the water outlet pipeline,VibelSingle stage slurry pump, and After that, cut off the power supply of the motor. If the temperature of the environment is low,VibelSubmersible non clogging slurry pump, open the square plug at the lower part of the pump body to remove the remaining water to avoid frost cracking. During operation, the maximum temperature of the bearing shall not exceed ℃, and the quantity of calcium base grease used for lubricating oil bearing shall be the same as that of the bearing bodyVibel,VibelWQ submersible pump parameters,   If the three-phase current of the submersible sewage pump is large and stable, the submersible pump cannot be started. The reason can only be understood from the submersible pump. Submersible pump bearings may be damaged and the pump may be blocked. The impeller is full of groceries. Submersible pumps shall not be used for sundries, such as those wrapped around the pump shaft  The hardened mud layer collapses after softening, avoiding the phenomenon of burying the pump during use.Tlalpan,  The operating environment is different: the key difference between the submersible slurry pump and the vertical slurry pump lies in diving. During the operation of the vertical slurry pump, some parts intrude into the pit and cannot completely invade the slurry; The submersible slurry pump can completely penetrate below the slurry level.  During the process, the equipment must be regularly maintained and overhauled to avoid blockage. As the name suggests, the water pump is mainly used to transport water when it is used. The effect of normal pumps is often better when it is used, but in fact, we use it at ordinary times  The supply of shaft seal water must be ensured. It is strictly prohibited to operate without water, otherwise the mechanical seal will be burned.


VibelHorizontal slurry pumpRequirements for equipment



  Pump. In addition, the submersible slurry pump is mainly characterized by 'slurry', which is wear-resistant and particle passing.  Clean up the silt and other obstructions in or around the water pump.  With the continuous development of slurry pump technology, submersible slurry pump has also responded to the market demand. At the same time, this type of pump is especially suitable for the depth where the vertical slurry pump cannot operate. Pay attention when using the equipment. The submersible slurry pump can operate if its depth is less than m, but it exceedsBidding,   If the hot water within ℃ is recommended, and the external tap water shall be connected for cooling during operation, otherwise the motor will not be burned due to too high medium temperature.  Rate loss, so shaft power = effective power + lost power.  Some of them are OK. For irrigation and other purposes, in fact, sewage submersible pump and seawater submersible pump.quality  The above is the correct sequence of impeller disassembly of submersible slurry pump. Because different types of pumps have some differences in structure, we also need to refer to the instructions when disassembling.  To solve this problem, we need to regularly inspect and repair the slurry pump. Our common maintenance methods are as follows: Auscultation: when the submersible slurry pump works normally, the accompanying sound has a certain melody and rhythm. As long as you are familiar with and master these normal melodies and rhythms, you can  During adjustment, firstly loosen the support cover, then compress the nut, and then loosen the bearing seat. After adjusting the screw, tighten the compression nut of the bearing seat evenly to make the assembly move towards the pump head. It is necessary to turn the trolley while tightening until the plate does not move. Rotate according to the pump operationVibel,  The of descending axial force can be used for slurry transportation in power plants, hydraulic and other professions; The mechanical seal is tight and reliable, and the leakage probability does not exceed drops /min, explosive, toxic, strong corrosive and valuable liquids or materials with high temperature, high pressure and low temperature.  The submersible slurry pump and equipment can also choose to add some water inlet detection devices according to the actual use needs. The overheat monitoring devices are often used in a large amount in time, and the pump and motor of the equipment used in time are the same shaft, so   in addition the noise method directly detects the noise of the equipment in the detection process, but such measurement will also be affected by the surrounding noise so in fact, such measurement is not very accurate.

comment list
  • Baxin Trading Company

    VibelHorizontal slurry pumpThe quality is good, completely beyond expectations, and the delivery speed is very fast.

  • Application software technology development

    Every time I receive the goods is very pleasant, but as long as I think of evaluating it, my head is big. Fortunately, a omnipotent friend recommended your home VibelHorizontal slurry pump, the price

  • Hanghui Technology Co., Ltd.

    Old acquaintances, things are as good as always, genuine VibelHorizontal slurry pump, outstanding cost performance

©2009-2024Industrial Microblog  Sitemap