When installing,BitomFixed hydraulic platform, disassembling, and adjusting the rotating mechanism, attention should be paid to ensuring that the middle line is parallel to the middle line of the gear, and its meshing surface is not less than %. The meshing clearance should be suitable for the brakes of each mechanism. The clearance between the brake wheels should be regularly checked and adjusted to ensure its flexibility and reliability. There must be no dirt on the friction surface and it must be cleaned with gasoline or diluent.When disassembling and adjusting the reverse organization of the equipment, attention should be paid to ensuring that the centerline of the reverse organization reducer is parallel to the centerline of the gear, and its meshing surface is not less than %. The meshing gap should be appropriate.BitomHow to maintain the cleanliness of hydraulic elevators. If more high-quality hydraulic oil is added, these additives will lose their effectiveness after a period of time.The cylinder head oil seal is too tight or the rod is bent it can prevent oil changes or blockage of system components. However, which can also cause noise during movement due to other forces. At this point, the oil seal or straightening rod must be replaced in a timely manner.Dunakeszi,Hydraulic lift cargo elevators belong to high-altitude work equipment. Small shaking of the scissor type structure is normal, but excessive deviation is a symptom. It is necessary to find the cause and make correct judgments in a timely manner. Generally speaking, operations above meters are generally allowed. Due to its own weight, devices above this height begin to vibrate in different ranges. The vibration range depends on factors such as weight, and intensity of high-altitude operations.Reason: The lowering speed valve is out of adjustment. Cleaning method: If the lowering speed valve is adjusted and if the adjustment is ineffective, replace it with a new valve.Stability: The workbench should evenly withstand % of the MAX load capacity and be stable at the MAX elevation.

After the pre installation is completed, the pre installed equipment should be fixed, and the positions of cables, oil pipes and components such as the pre installed frame should be confirmed to be correct before reinforcement work can be carried out. Reinforcement requires welding or screws, and the hydraulic cargo elevator after reinforcement has robustness and safety.Hydraulic elevators and load-bearing oil cylinders can directly act on the foundation pit, requiring low shaft strength, and brick or brick concrete structure shafts.Wholesale manufacturers of hydraulic cargo elevators have found that the market demand for hydraulic cargo elevators is also increasing. More importantly, some cargo loading and unloading work, as well as decoration, hotels, logistics, warehouses, supermarkets, etc., are commonly used in these situations, which are also specially processed and manufactured, and have some differences from the hydraulic cargo elevators we often see. There are significant differences in structure, shape, lifting speed, and the prices of hydraulic cargo elevators also vary. The hydraulic cargo elevators used in the decoration industry have a low lifting height, some only meters, and do not require many materials. He mainly promotes people, not goods, and rarely promotes goods, so the load is small,BitomLarge hydraulic lifting platform, but not inferior to the use of other hydraulic cargo elevators. He is stable, safe, interpretable, and durable enough to make hydraulic cargo elevators a good helper in the decoration industry. The function of hydraulic cargo elevators is gradually improving with our needs, and the properties we require are different. Wholesale manufacturers of hydraulic cargo elevators also manufacture according to our requirements.Quality assurance,The noise and oil level of the elevator oil cylinder are too low. From the air at the connection of the oil filter or joint to the oil, the coupling inside the oil cylinder is loose. The internal fault of the oil cylinder is that the installation of the oil cylinder motor is not concentric. From the motor, the air and oil at the moving shaft are blocked. The oil return pipe of the oil filter is loose, and the air or oil pipe is on the oil surface, Mixing air into the oil to eliminate: The concentricity should be adjusted to within .MM. The coupling should be repaired or the oil pump should be replaced to increase the oil volume above mm in the oil filter and joint positions. The rotating shaft sealing ring should be replaced to clean the oil filter screen, filter the oil, lock the return oil pipeline, and extend the return oil pipeline below the oil level. If there is air mixed in the oil or the air in the hydraulic cylinder is not completely discharged, it will cause cavitation under high pressure and cause significant noise. At this point, it is necessary to exhaust the air in a timely manner.Pay attention to checking each steel wire rope for signs of broken wires and loose drums. If it exceeds the relevant rules, it is necessary to replace it immediately. The protection of steel wire ropes should strictly follow the rules of GB-.There is a phenomenon of self stopping when running up and down. Due to poor contact of the safety protection switch, and the oil temperature is between ~ ℃. Use a large flow rate to remove impurities from the system as much as possible. The hydraulic system needs to be cleaned repeatedly three times or more, and after each cleaning, the system should be drained while the oil is hot. After cleaning clean the filter and add new oil after using a new filter element.Safety production,Lifting mechanism: The workbench should be ensured to rise and fall smoothly, and there should be no jumping lifting phenomenon. All moving parts should be flexible when moving, and there should be no jamming devices. The lifting system of the elevator is divided into electric or manual hydraulic systems, and there should be no leakage at all components, pipelines, and the output machinery is the speed and traction force during linear motion. All these parameters are achieved through changes in working volume, so hydraulic cylinders are a type of volumetric actuator. In order to meet the different needs of various machinery, hydraulic cylinders have different structures and hydraulic capabilities. According to hydraulic capacity, it can be divided into single acting hydraulic cylinders and double acting hydraulic cylinders. According to its structural characteristics, it can be divided into plunger hydraulic cylinders and hydraulic cylinders. Telescopic hydraulic cylinders and hydraulic cylinders are both referred to as the heart of hydraulic cargo elevators. How to maintain the heart of a hydraulic cargo elevator? Professional elevator manufacturers guarantee quality, service, and quality. Your satisfaction is our pursuit! Welcome to inquire by phoneSet up warning lights around the guide rail type hydraulic cargo elevator equipment, and the warning lights will light up to warn operators when loading and unloading materials. Idle personnel are prohibited from entering the operating range.Bitom,For hydraulic cylinders in hydraulic elevators, it is not practical to change their effective working area A (equivalent to displacement) to adjust the speed. Generally, the speed can only be adjusted by changing the flow rate. For variable displacement motors, speed regulation can change both the flow rate and the motor displacement.Regularly check whether each organization is functioning properly and whether there is noise. If problems are found, they should be promptly cleaned up.Selection of the location of the loading and unloading lifting platform In order to reduce the cost of material handling, the location of the platform should be selected to minimize the distance of the handling tools and vehicles in the factory. It is much easier to move a fully loaded transport vehicle to a designated location outside the building than to transport the loaded materials one by one to the designated location indoors. When selecting a platform location, full consideration should be given to the production process and operational needs of the factory. There are two modes of platform layout: merging: loading and unloading on the same platform.