According to the national standard of hot rolled H-section steel in China (GB / t-, H-section steel is divided into narrow flange, wide flange and steel pile, whose codes are Hz, HK and Hu respectively. Narrow flange H-section steel is suitable for beams or compression bending members while wide flange H-section steel and H-section steel piles are suitable for axial compression members or compression bending members. Compared with H-section steel, W, IX and iy are not as good as H-section steel under the premise of equal weight.The general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, not very little aluminum alloy, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.Takavano,According to the historical records of the recent four years, the zinc price in the first quarter was generally higher than that in the whole year, zinc prices continued to decline in the first quarter of , and showed a trend of accelerating the decline day by day. There are two key reasons for the beginning of this year. First, the vicious change of the real estate industry has led to a rapid decline in the growth rate of China&#;s consumption of galvanized pipe and seamless steel pipe and even a contraction month on month; Secondly, the blind expansion of galvanized pipe factory confused the sense of rhythm of supply and demand balance.Defects of alloy pipe and solutions:Aral, Cold extrusion. This kind of processing method is more purposeful. Before the preparation of steel processing and extrusion molding, when the extrusion molding is used for mm diameter pipe fittings, the investment of machinery and equipment is less, so the raw material consumption is also very small, the cold extrusion method must have large cargo capacity and high-power machinery and equipment. Therefore, the automatic control system will be upgraded.Because the section size of ordinary I-beam and light I-beam is relatively large and narrow, the moment of inertia of the two main shafts on the section is quite different, which limits its application range. I-beam shall be selected according to the requirements of design drawings. In the structural design, the use of I-beam should be reasonably selected according to the mechanical properties, weldability and structural size of I-beam.Whether I-section steel is ordinary or light, because the section size is relatively high and narrow, the moment of inertia of the two main axes of the section is quite different, so it can only be directly used for members bent in the plane of their web or form lattice stressed members.

H-shaped steel groove is deep and thick, and can withstand forces in two directions.The electric welding reinforcement mesh can reduce the damage and consumption to the reinforcement processing process. According to statistics, it can also save about % of the steel. After it is transported to the site according to the construction degree of the project,TakavanoHigh strength plastic alloy pipe, it can be hoisted to the working face. There is no need to set a reinforcement processing site on the site, which saves the site and increases the management level of the site. At the same time, it can also solve the problems of noise pollution caused by straightening reinforcement. H-section steel is an economic section steel with better mechanical properties than I-section steel. It is named because its section shape is the same as the English letter 'H'. The flange of hot rolled H-beam is wider than that of I-beam, with large lateral stiffness and strong bending resistance. Under the same specification, H-beam is lighter than I-beam.technical service,Due to the relatively high and narrow section size of ordinary I-beam and light I-beam, the moment of inertia of the two main sleeves of the section is quite different, which makes it very limited in the scope of application. The use of I-beam shall be selected according to the requirements of design drawings. The defects can be removed by grinding with sand wheel, but the remaining wall thickness must be within the allowable standard.Main uses: as a finished material, flat steel can be used to make hoop iron, tools and mechanical parts,TakavanoPrice quotation of No. 16 I-beam, and used as building frame structural parts and escalators in buildings. Flat steel is divided into two types according to its shape: plane spring flat steel and single-sided double groove spring flat steel. Hot rolled spring flat steel is mainly used to manufacture leaf springs for automobiles, tractors, railway transportation and other machinery.

Mixed Scabs are distributed periodically, and the situation after casting and rolling is significant through edge flame peeling crack inspection or billet scratch flame removal.Fair price,The delivery length of I-beam is divided into fixed length and double length, and the allowable difference is specified in the corresponding standards. The length selection range of domestic I-beam is divided into -,TakavanoHow much is 12Cr1MoVG alloy tube per ton, - and - according to different specification numbers. The length selection range of imported I-beam is generally -.Due to the impact of poor visual . Only through the application of mesh and the overall stiffness can we see the potential of demand. The application of steel data is a high one, such as the reuse rate of mesh and reinforcement installed in the current mesh production company and the treatment of corrosion. The design strength value of circular reinforcement and the design strength value of welded reinforcement mesh. According to the equal strength substitution principle and considering comprehensive factors, the use of steel welded mesh plate can save the use of steel bars in the steel welded mesh plate factory. And the reinforcement mesh needs to be processed after it is shipped to the site, so there is no wear.Stages needing attention in the production and manufacture of alloy tubesTakavano,Classification introductionPlan scheme : Martensitic chromium alloy pipe and chromium alloy pipe with Cr composition exceeding %, without high carbon steel and high chromium alloy pipe. The aqueous solution contains % sodium cyanide % ~ % (volume ratio) the solution temperature is ~ ℃, and the solution time is min.→ I-beam can be processed into T-beam, and honeycomb beam can be combined to form various section forms, which greatly meets the needs of engineering design and manufacturing.