Methods of exerting efficiency in application of C-section steel Mixed pass system. According to the characteristics of rolling mills and products, in order to give full play to the advantages of their respective systems and overcome their disadvantages, mixed pass system is often adopted, that is, the combination of more than two systems. For example, straight leg cross rolling pass system is adopted for finished hole and front hole of finished product, and bent leg cross rolling system is adopted for other passes; or direct rolling system is adopted for rough rolling hole and straight rolling system is adopted for the last ~ finish rolling holes Leg oblique tie hole, etc.Cochani,Seamless pipeAs shown in the name, I-beam is an I-shaped section steel. The inner surface of the upper and lower flanges has an inclination, generally :, which makes the outer flange thin and the inner flange thick. Therefore, the section characteristics of I-beam in the two main planes are very different, and it is difficult to give full play to the strength characteristics in application. Although the thickened I-beam has also appeared in the I-beam market, the structure of the I-beam has determined its torsional performance.Magnitogorsk,According to the theory of steel structure, the I-beam flange should be stressed, that is the I-beam should be standing rather than lying down.X-ray or ultrasonic testing shall be carried out for repair welding of alloy pipe, dead end welding of strip steel and circumferential seam. For the spiral welding of steel for the transportation of flammable general liquids, yibai%sx ray or ultrasonic testing shall be carried out. For the spiral welding of alloy pipes for the transportation of water,CochaniWelded pipe manufacturer, gas, heating steam and other general liquids, X-ray or ultrasonic testing sampling inspection (%) shall be carried out.The production process can be summarized as follows: pre leveling → finishing → straightening → post leveling. Flat steel / A / B steel with width of -, thickness of -, rectangular section and slightly pure edge. Flat steel can be finished steel,CochaniWhich is easy to use for steel bar software, or it can be used as blank for welded pipe and thin slab for laminated thin plate.

Alloy pipe can be divided into round steel pipe and special-shaped steel according to different cross-sectional area. Because the circular area is large on the premise of the same side length, a large amount of liquid can be transported with an annular tube. In addition, the bearing force is more symmetrical. Therefore, most seamless steel pipes are round steel pipes.Oxygen blowing welded pipe: it is used as steel blowing pipe. Generally, small-diameter welded steel pipe is used. There are eight standards from / inch to inch. Made of , , , or q-q steel strip. In order to prevent corrosion, some are aluminized.However, what we need to do now is to improve the production technology level of China&#;s production process of C-section steel, and step up the formulation of relevant industry standards and inspection standards. C-section steel manufacturers should keep close contact with truck manufacturers and communicate more. In this way,Cochani76 seamless pipe price, it is more conducive for C-section steel manufacturers to produce C-section steel products suitable for truck industry.Total quality managementThe general alloy pipe with improved performance is variable and has high application value. The alloy pipe contains more Cr and is heat resistant Low temperature resistance Corrosion resistance. There is no aluminum alloy in plain carbon seamless steel pipe, and the alloy pipe is used in crude oil Aerospace Chemical plant Power engineering heating furnace. Because the physical properties of alloy tubes are easy to change and adjust.Alloy tube is widely used in our daily life not very little aluminum alloy, which provides us with great assistance.Classification introduction

Defects of alloy pipe and solutions:Packaging strategy,Alloy pipe is a spiral seam seamless steel pipe, which is made of hot-rolled strip steel coil, often processed by warm extrusion and welded by automatic double wire double side arc welding process. The alloy pipe sends the hot-rolled strip steel to the welded pipe unit, and the hot-rolled strip steel is extruded through multiple passes. The hot-rolled strip steel is rolled slowly to produce annular pipe material with open mouth gap. Adjust the reduction amount of the extrusion roll to control the welding gap at ~ mm and make both sides of the weld flush.The third is the welding machine, which must ensure reliable performance and meet the process needs; The welding machine must have qualified ammeter and voltmeter to ensure the correct implementation of welding process. The welding cable shall not be too long, and the welding parameters shall be adjusted when it is too long.The sodium cyanide passivation treatment of alloy pipe can be divided into four categories. Before passivation treatment, the surface of alloy pipe shall be clear of oil stains, pickled and passivated. Passivation treatment can be carried out only after the surface is cleaned, and the workpiece of alloy pipe products can be infiltrated into aqueous solution. The passivation treatment of the alloy tube in sodium cyanide transforms the surface layer into a very thin passivation treatment film, which determines that the color of the surface layer has no change before and after passivation treatment,I-beam can be divided into four types according to shape: cold-formed equal edge I-beam, cold-formed unequal edge I-beam, cold-formed inner crimping I-beam and cold-formed outer crimping I-beam.I-beam is a kind of economical section steel with better section mechanical properties. Its characteristics are as follows: Remove defective pipes within the allowable length.