Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole,SnoreThree ton cargo elevator, and tighten the inner hexagon. After that, remove the motor shaft key.The hydraulic lifting platform can be divided into: four-wheel mobile type, two-wheel traction type, car modified type, car type auxiliary self-propelled type, and the lifting height ranges from a meter to s meter.Snore,What safety tools are there on mobile lifts Explosion-proof valves: often seen in large hydraulic equipment, especially heavy equipment,SnoreThree story cargo elevator,SnoreHeavy industry guide rail type cargo elevator, the main effect can prevent the oil circuit from bursting or the pressure of the oil circuit is too high to cause problems with the equipment. Regarding small lifts The installation of explosion-proof valves depends on the needs of customers, but large-scale equipment basically needs to be installed.Check the limit switch to see if all the limit switches are loose. If so, etc. are loose, if any should be reinforced immediately; ensure that the hydraulic lifting platform rises and falls smoothly; outriggers (for high-altitude operating platform)Herrez delavrontra,The water cooling of the hydraulic station is generally tube-type water cooling, and its type selection is based on the heat load to calculate the heat exchange area, while its air-cooled elevator is carried out by using an air cooler, and it is The heat transfer capacity is calculated according to the heat load, and then the type selection calculation is carried out under the condition that the flow rate can be satisfied. Therefore, these two kinds of cooling are not the same, and there is a big difference. Long-term promotion of freight elevator factories and other, Long-term cooperation, mutual benefit and win-win. If you choose the wrong supplier, you will be overwhelmed with all kinds of after-sales troubles in the later stage. Recently, I have seen many netizens report the problem of very loud oil cylinders. Today, the editor will simply popularize the knowledge for everyone.Goods should be stacked on the platform and not tilted. When the freight elevator goes up and down beyond the range of the platform, no one should stand around to watch.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, scratches, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.

Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.The lifting stage can realize the lifting of the double-layer platform. According to needs, it can also be assembled into ladder-shaped, multi-level ladders to form a group of lifting platforms, which can form different steps within the travel range, enriching the multi-functional effect of the stage. For studios, cultural and sports venues, etc., the telescopic stage adopts an effective guiding system, so that the gap between the telescopic stage and the fixed stage is small during the translation process the operation is stable, the speed changes steplessly, the synchronous device, and the electric drive is driven by low speed and large torque. The device is parallel, free, and stretches in place during the expansion and contraction process, and it can automatically level the stage. The application and characteristics of the stage lift. The rotating stage has various functions such as lifting, rotating, and tilting. Explosion-proof and other protective measures. Make the stage stable and reliable, widely used in auditoriums, theaters, multi-functional halls, cultural and sports venues, hotels and other cultural and entertainment venues.Correct construction elevator site inspection First of all, we need to check the foundation to see if there is any water accumulation, and check whether the grounding system meets the requirements. We also need to check how the structural bolts of the frame are fastened and whether there are any cracks in the welds. We need to follow the instructions to set it up. In mechanical transmission, it can be divided into two types: open type and closed type. Of course, the lift also has a lot of safety equipment.Word of mouth recommendation,How to effectively prevent electric shock by using a hydraulic lifting platform It is very common to add a leakage protector and the cost is not high. It is both affordable and safe, and can effectively prevent electric shock.The safety device of the guide rail hydraulic lifting platform The mechanical part of the guide rail hydraulic lifting platform mainly includes the hydraulic system and the mechanical device.Conscientiously write the special construction plan for installation and construction, and make safety technical disclosures to the installers.

The scissor-type fixed lifting platform is a kind of transportation and handling equipment for transporting goods from a certain height to another height. After the operation is completed, the platform is level with the ground, does not occupy the ground space, and does not affect the passageway.Safety and health,The motor winding is short-circuited. When a short-circuit fault occurs in the motor winding, the short-circuit current is much larger than the normal operating current, which increases the copper loss of the winding, causing the winding to overheat and even burn out.How to maintain the elevator correctly and replace the hydraulic oil of the elevator regularly: the hydraulic oil used in the elevator is divided into winter and summer. It is not noticed until the hydraulic cylinder of the elevator is working abnormally.Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.Snore,Many people think that the strength of the elevator itself is relatively high when using the elevator, so they did not strictly follow the installation method in the manual during the installation process, but they do not know that this will cause increased wear and tear of the parts and inflexible operation, and pay attention to the work The installation precautions corresponding to the environment should not be ignored. Correct installation, use and maintenance of elevators are an important part of ensuring the normal operation of mechanical equipment. Therefore when you install the elevator, please be sure to strictly follow the installation and use related matters below, and assemble and use it carefully.Regular maintenance Regularly check whether the circuit system of the hydraulic lifting platform is loose, and check whether the wires and cables are aging and damaged, which may cause leakage of the line. If there is, it should be repaired in time to avoid electric shock.The daily maintenance of the hydraulic lifting platform in normal use is essential, but even if there is normal maintenance on the equipment, any possible problem cannot be ignored, so in order to ensure that the process of using the hydraulic lifting platform for each operation What aspects do we need to check before operation? Today, the editor will give you a popular science.