Secondly, there must be no dirt on the friction surface. If there is dirt, it needs to be washed off with gasoline or thinner; the gear box, gearbox, external gear and other parts of the equipment and the hydraulic oil must be in accordance with the requirements in the table; Correctly maintain the hydraulic guide rail lift. Regularly check whether the wire ropes in each part are broken or loose. If this phenomenon is found,Xinqiu4-ton hydraulic lifting cargo elevator, replace them in time. If there is any looseness, it should be tightened in time. The connecting bolts of the equipment should be checked for tightness when the body is under pressure. All connecting shafts should be equipped with cotter pins; check whether each mechanism is operating normally, whether there is noise or failure , to eliminate all faults in a timely manner; when installing, dismantling and adjusting the slewing mechanism of the equipment, it is necessary to pay attention to the parallelism between the reducer and the center line of the gear, and the appropriate meshing gap; conduct a comprehensive inspection of the equipment regularly, whether the motor is overheated,Xinqiu13 meter guide rail type cargo elevator, replace it in time and continue to run after troubleshooting; ensure that the bearings of the motor, each box, distribution box and brushes must be kept clean and the travel switch points of each safety device must be safe and reliable.Nowadays, small and medium-sized enterprises are holding products with the idea of ​​good quality and favorable price.Xinqiu,The lifting platform needs to be placed in a ditch position, and the corresponding anti-slip work should be done; remove the gear box of the equipment, remove the shaft holding oil box, take out the lower tile and oil absorber; test the car slowly, and check whether the surface around the shaft holding diameter is severely damaged ; If the damage is serious and the tungsten gold is occupied, it should be smoothed with oilstone; under the motor, and the sleeper is carried on the edge of the ditch inside the rail, and the motor is regularly pulled by a jack to remove the upper tile; the important part of the lifting platform How to deal with equipment damage Check the status of the bearing bush and oil absorber, investigate the cause of damage replace the bearing bush, clean the shaft oil box; after assembling all parts, install a new oil absorber on the oil box for the shaft, clean the shaft Oil; gear box gear oil in accordance with the regulations; axle box bearing burnout is the most common bearing burnout of the outer row, and in serious cases, the axle box and the wheel set will be fixed together, affecting the operation of the equipment.Use Hydraulic lifts are widely used in various industrial enterprises and production lines such as automobiles, containers, mold manufacturing, wood processing, chemical filling, etc., to meet the lifting needs of different operating heights, and can be equipped with various table forms (such as balls, rollers, Turntable steering, tilting, telescopic),XinqiuLifting cargo elevator 1 ton, with various methods (separate, linkage, explosion-proof), with the characteristics of stable and accurate lifting, frequent starting, effectively solving the difficulties of various lifting operations in industrial enterprises, so that Production operations freely. The professional elevator factory has advanced technology, strict testing, more affordable prices, and more discounts are in progress, welcome to consult.Alhad,What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.What is the new price of fixed lifts? Fixed lifts are currently very popular in the market. Due to different manufacturers, different materials, different rated loads, and different brand awareness the prices are also different. The current price of fixed lifts produced in the domestic market: rated load - tons, height of meters, table size mm *mm, the price is about - yuan; the rated load is - tons, the height is meters, the table size is mm*mm, the price is about yuan. Rated load lift height, table size of each fixed liftDifferent. (Specific bearing capacity and rising height can be customized according to user requirements)Before the elevator manufacturer connects the motor to the elevator, please make the keyway of the motor shaft perpendicular to the tightening bolt. In order to ensure uniform force, please screw on the mounting bolts at any diagonal position first, but do not tighten them tightly, then screw on the other two mounting bolts at diagonal positions, and then tighten the four mounting bolts one by one. Finally, tighten the tension bolts. All tightening bolts need a torque wrench to fix according to the marked fixed torque data and check whether the lift and lifting platform are used.How should we check the construction site of the construction hoist? you know?

Unscrew the screw on the dust-proof hole outside the flange of the elevator, adjust the PCS system ring to align the side hole with the dust-proof hole, and tighten the inner hexagon. After that, remove the motor shaft key.It is strictly forbidden to combine the two layers of the top lining of the safety helmet into one layer.After the goods are transported, clean up the debris on the platform.query,Outriggers: mechanical outriggers, hydraulic outriggers, ordinary hand-operated outriggers, pull-out outriggers.Fixed lift is a kind of transportation equipment that directly lifts and unloads goods from the ground. It is mostly used in places such as goods transportation between height differences in production lines, materials on and off the assembly line, parts lifting during large-scale equipment assembly, and fixed three-dimensional parking. So what is the new price of the fixed lift?What are the maintenance rules for hydraulic lift machinery? The brakes of each mechanism should be checked frequently and the gap between the brake shoe and the brake wheel should be adjusted to ensure flexibility and reliability. There should be no dirt on the friction surface, and if there is dirt, it must be washed off with gasoline or thinner.

Hydraulic pump station: special pump station for domestic lifting platform, protection device outside the pump station imported from Italy: organ m type, iron plate seal type.safety requirements ,Test the freight elevator every day to see if the freight elevator can operate normally.Working at heights is very common now, and lifts are very popular in the market. Many high-level transportation tasks are completed by elevators, attention should also be paid to the installation of the lift, otherwise there will be problems, and no one wants to see such a situation happen. What are the installation precautions for the lift?Walking: assisted self-propelled, two-wheel traction self-driving, and car modified.Xinqiu,Frequently check whether the various mechanisms are operating normally and whether there is any noise. If a fault is found, it must be eliminated in time.The wrong connection of the motor of the elevator When a coil, coil group or one-phase winding is reversed, it will cause a serious imbalance in the three-phase current and cause the winding to overheat.Anti-corrosion measures for the body of aerial work vehicles Pay attention to small scratches. The paint surface of aerial work vehicles is often corroded. In addition to common collisions, small rocks on the driving tires, there may also be a peeling paint spot, and a small rust will appear after a long time. Because most of these scars are small, they are easy to ignore. Therefore, check regularly, the engine compartment cover and its surroundings, and once found, go to a professional beauty shop for processing.